Configuration Files |  |
Configuration File "ToolikNetRSConfigFile"# ++ FBCfg v1
# Configuration File, Original Name = ToolikNetRSConfigFile
# created Tue May 24 00:18:07 UTC 2005
## file /etc/sysconfig/gpssd.config
0 serial 115200:N:N 0 ppp 1 0
1 OFF-serial 9600:N:N 0 met 10 0 0
2 serial 115200:N:N 0 ppp 1 0
3 serial 9600:N:N 0 cmr 10 1
## end of file /etc/sysconfig/gpssd.config
## file /etc/sysconfig/met.conf
## end of file /etc/sysconfig/met.conf
## file /etc/sysconfig/advertise
## end of file /etc/sysconfig/advertise
## file /etc/sysconfig/dialout
## end of file /etc/sysconfig/dialout
## file /etc/sysconfig/mgetty+sendfax/mgetty.config
#
# mgetty configuration file
#
# this is a sample configuration file, see mgetty.info for details
#
# comment lines start with a "#", empty lines are ignored
# ----- global section -----
#
# In this section, you put the global defaults, per-port stuff is below
# set the global debug level to "4" (default from policy.h)
debug 0
# set the local fax station id
fax-id 49 115 xxxxxxxx
# access the modem(s) with 38400 bps
#speed 38400
# use these options to make the /dev/tty-device owned by "uucp.uucp"
# and mode "rw-rw-r--" (0664). *LEADING ZERO NEEDED!*
#port-owner uucp
#port-group uucp
#port-mode 0664
# use these options to make incoming faxes owned by "root.uucp"
# and mode "rw-r-----" (0640). *LEADING ZERO NEEDED!*
#fax-owner root
#fax-group uucp
#fax-mode 0640
# ----- port specific section -----
#
# Here you can put things that are valid only for one line, not the others
#
# Zoom V.FX 28.8, connected to ttyS0: don't do fax, less logging
#
#port ttyS0
# debug 3
# data-only y
# some other Rockwell modem, needs "switchbd 19200" to receive faxes
# properly (otherwise it will fail with "timeout").
#
#port ttyS1
# speed 38400
# switchbd 19200
# ZyXEL 2864, connected to ttyS2: maximum debugging, grab statistics
#
#port ttyS2
# debug 8
# init-chat "" \d\d\d+++\d\d\dAT&FS2=255 OK ATN3S0=0S13.2=1 OK
# statistics-chat "" AT OK ATI2 OK
# statistics-file /var/log/statistics.ttyS2
# modem-type cls2
# direct connection of a VT100 terminal which doesn't like DTR drops
#
#port ttyS3
# direct y
# speed 19200
# toggle-dtr n
# SerialPort1
# SerialPort1
port console
direct y
speed 115200
toggle-dtr n
debug 0
# SerialPort2
port tts/1
direct y
speed 115200
toggle-dtr n
debug 0
# SerialPort3
port tts_max0
direct y
speed 115200
toggle-dtr n
debug 0
# SerialPort4
port tts_max1
direct y
speed 115200
toggle-dtr n
debug 0
## end of file /etc/sysconfig/mgetty+sendfax/mgetty.config
## file /etc/sysconfig/ppp/options.console
nocdtrcts
192.168.0.1:192.168.0.10
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.console
## file /etc/sysconfig/ppp/options.tts.1
192.168.0.1:192.168.0.20
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.tts.1
## file /etc/sysconfig/ppp/options.tts_max0
192.168.0.1:192.168.0.30
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.tts_max0
## file /etc/sysconfig/ppp/options.tts_max1
192.168.0.1:192.168.0.40
nocrtscts
local
## end of file /etc/sysconfig/ppp/options.tts_max1
## file /etc/sysconfig/ref_stn.config
AntSerial: 12572725
AntTextSerial:
AntType: 86
AntName: Zephyr Geodetic
AntHeight: 0.000
AntMethod: -1
Lat: 68.627534208333
Lon: -149.597757500000
Height: 740.1290
RTCM_ID: 284
CMR_ID: 28
BINEX_ID:
StationName: TOOL2845
StationDesc: Toolik Field Station - IAB/UAF (907)474-2466
## end of file /etc/sysconfig/ref_stn.config
## file /etc/sysconfig/sessions
#Name Enb Type Date/Time Duration DataType FileTemplate
15sec_24hr 0 cont 0 1440 T00:15:300:0:0 b:0:0:0
30sec_24hr 0 cont 0 1440 T00:30:300:0:0 z:0:1:0
5sec_24hr 0 cont 0 1440 T00:5:300:0:0 c:0:0:0
RINEX 1 cont 0 1440 T00:30:300:0:0 r:0:1:0
ToolikUser 1 cont 0 60 T00:1:60:0:0 d:0:1:0
## end of file /etc/sysconfig/sessions
## file /etc/sysconfig/sleepmode
no yes 24 10
## end of file /etc/sysconfig/sleepmode
## file /etc/sysconfig/autoDelete
Reserved 1000000 yes
## end of file /etc/sysconfig/autoDelete
## file /etc/sysconfig/stinger.cfg
put meas_rate 10
put waas_mode off
put pps_mode off pos
put sv_masks E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E E
put waas_mode off
put waas_sv_masks E E E E E E E E E E E E E E E E E E E
put clock_steering off
put everest off
put l2cs_mode off
put elev_mask 0
put pdop_mask 50
## end of file /etc/sysconfig/stinger.cfg
## file /etc/sysconfig/vsleep
11.000
## end of file /etc/sysconfig/vsleep
## file /etc/sysconfig/extRefFreq
REFSOURCE="Internal"
## end of file /etc/sysconfig/extRefFreq
## file /etc/sysconfig/interfaces
auto lo
iface lo inet loopback
up route add -host 127.0.0.1 lo
auto eth0
iface eth0 inet dhcp
up ifconfig eth0 mtu 1500
## end of file /etc/sysconfig/interfaces
## file /etc/sysconfig/resolv.conf
nameserver 137.229.34.137
## end of file /etc/sysconfig/resolv.conf
## file /etc/sysconfig/ftp.conf
ftpEnabled yes
standardPort yes
alternatePort 8021
anon disabled
named enabledDelete
admin disabled
namedPassword JEtOnUG.tqKZQ
adminPassword
## end of file /etc/sysconfig/ftp.conf
## file /etc/sysconfig/iptables.conf
## end of file /etc/sysconfig/iptables.conf
## file /etc/sysconfig/httpPorts
## end of file /etc/sysconfig/httpPorts
## file /etc/sysconfig/ntp.conf
#
# Undisciplined Local Clock. This is a fake driver intended for backup
# and when no outside source of synchronized time is available. The
# default stratum is usually 3, but in this case we elect to use stratum
# 0. Since the server line does not have the prefer keyword, this driver
# is never used for synchronization, unless no other other
# synchronization source is available. In case the local host is
# controlled by some external source, such as an external oscillator or
# another protocol, the prefer keyword would cause the local host to
# disregard all other synchronization sources, unless the kernel
# modifications are in use and declare an unsynchronized condition.
#
server 127.127.29.0 # Fireball stinger reference time
#
# Authentication delay. If you use, or plan to use someday, the
# authentication facility you should make the programs in the auth_stuff
# directory and figure out what this number should be on your machine.
#
authenticate no
# directory for statistics files
#statsdir /var/log/ntp/ # the final slash is required
# Enable data logging
#filegen loopstats file loopstats type day enable
#filegen peerstats file peerstats type day enable
#filegen clockstats file clockstats type day enable
server 127.0.0.1 # External Server
## end of file /etc/sysconfig/ntp.conf
## file /etc/sysconfig/step-tickers
127.0.0.1
## end of file /etc/sysconfig/step-tickers
## file /etc/sysconfig/htaccess.fileaccess
AuthType Basic
AuthUserFile /etc/sysconfig/htpasswd
AuthGroupFile /etc/sysconfig/htgroups
AuthName FileAccess
require group fileaccess
## end of file /etc/sysconfig/htaccess.fileaccess
## file /etc/sysconfig/htaccess.gpsadmin
AuthType Basic
AuthUserFile /etc/sysconfig/htpasswd
AuthGroupFile /etc/sysconfig/htgroups
AuthName GpsAdmin
require group gpsadmin
## end of file /etc/sysconfig/htaccess.gpsadmin
## file /etc/sysconfig/htaccess.sysadmin
AuthType Basic
AuthUserFile /etc/sysconfig/htpasswd
AuthGroupFile /etc/sysconfig/htgroups
AuthName SysAdmin
require group sysadmin
## end of file /etc/sysconfig/htaccess.sysadmin
## file /etc/sysconfig/htgroups
sysadmin: sysadmin toolik
gpsadmin: sysadmin toolik
fileaccess: sysadmin toolik
## end of file /etc/sysconfig/htgroups
## file /etc/sysconfig/htpasswd
sysadmin:fREeTt.t4yGaM
toolik:DrxchYOHTcqBI
## end of file /etc/sysconfig/htpasswd
## file /etc/sysconfig/sysname
tool
## end of file /etc/sysconfig/sysname
